活塞风对地铁车站站台滑动门风压的影响

基于有限体积法建立了地铁车站三维静态数值计算模型,对列车阻塞隧道时站台滑动门所受的活塞风压进行了计算研究;分别对单、双两种活塞通风条件下,不同活塞风速、阻塞比、滑动门位置对滑动门所受风压的变化规律进行了分析。结果表明,双活塞通风能够有效减弱活塞风对滑动门的风压;单活塞通风条件下,滑动门在最不利位置时,需克服的最大风压约为230 Pa。     

Validation and application of nonlinear hydrodynamics from CFD in an engineering model of a semi-submersible floating wind turbine

Nonlinear hydrodynamics play a significant role in accurate prediction of the dynamic responses of floating wind turbines (FWTs), especially near the resonance frequencies. This study investigates the use of computational fluid dynamics (CFD) simulations to improve an engineering model (based on potential flow theory with Morison-type drag) by modifying the second-order difference-frequency quadratic transfer functions (QTFs) and frequency-dependent added mass and damping for a semi-submersible FWT. The results from the original and modified engineering models are compared to experimental data from decay tests and irregular wave tests. In general, the CFD results based on forced oscillation tests suggest increasing the frequency-depending added mass and damping at low frequencies compared to first order potential flow theory. The modified engineering model predicts natural periods close to the experimental results in decay tests (within 5%), and the underprediction of the damping is reduced compared to the original engineering model. The motions, mooring line tensions and tower-base loads in the low-frequency response to an irregular wave are underestimated using the original engineering model. The additional linear damping increases this underestimation, while the modified QTFs based on CFD simulations of a fixed floater in bichromatic waves result in larger difference-frequency wave loads. The combined modifications give improved agreement with experimental data in terms of damage equivalent loads for the mooring lines and tower base.     

The uplift capacity of single-plate helical pile in shallow dense sand including the influence of installation

The helical pile has been used to resist the tension for a long time. However, the prediction of the uplift capacity of helical piles including the influence of installation is still a challenge in design. Based on the change in stress according to Mohr-Coulomb failure criterion, a simple theoretical method has been developed, which can calculate the uplift capacity of shallow pre-embedded circular plate anchors and the uplift capacity of helical piles installed by torque and compression. In order to analyse the influence of installation process of a single-plate helical pile on its uplift capacity and verify the theoretical model, a series of model tests have been conducted in dense saturated sand. The single-plate helical piles with different out diameters of helixes have been installed with different installation speeds, and then, the single-plate helical piles have been moved up monotonically. The test results show that the installation speed and the size of the out diameter of the helix have significant influence on the uplift capacity of the helical piles, and the results of the theoretical method have a good fit with the test results. Using this simple theoretical method, the designer can easily predict the uplift capacities of helical piles, which includes the influence of installation.     

考虑高铁客运产品间交叉弹性的动态票价策略

将由特定高铁列车所提供的起讫点间的旅客运输服务定义为单个高铁客运产品。随着高速铁路越来越"公交化",同一起讫点间客运产品间的可替代性越来越强,票价的调整有了更精细化的要求。用经济学中的交叉弹性理论描述客运产品间的可替代程度,用指数需求函数描述客运产品的需求与票价的关系,构建并求解高铁动态票价优化模型,对客运产品间不同可替代程度下的最优动态票价策略进行研究。结果显示:高铁客运产品间的可替代性会影响票价策略的选择,且客运产品间可替代程度的增加是否有利于客票收益的提高与可行折扣票价集合的选取有关。     

非线性混合海况下近海风机塔筒底部载荷的动力响应

本文主要研究在非线性混合海况(即风浪和涌浪组合海况)下,以NREL 5MW_Baseline Monopile近海风机为研究对象,对其塔筒底部(基线)所受到的剪力和弯矩载荷的动力响应进行仿真。在近海风机的时域仿真中,选用了Ochi-Hubble六参数波浪谱,并编制了该谱的程序嵌入到FAST中进行编译。计算过程中,共进行了20次10 min的仿真分析。对于得到的短期载荷,给出了波高程,塔筒底部首尾向剪力和弯矩在线性与非线性不规则波作用下的时程曲线对比图。采用分块最大值法对每一次的短期载荷提取极值,并基于20次仿真所得的极值,给出了塔筒底部首尾向剪力与弯矩在线性与非线性不规则波作用下的超越概率曲线对比图。研究表明,在非线性混合海况下进行近海风机塔筒底部载荷的动力响应研究,计算结果对工程实际应用具有指导意义。     

M型风电运维船船型设计与波浪增阻和耐波性能研究

本文基于三体风电运维船船型,结合M型船的特征要素设计改造出M型风电运维船。利用数值仿真技术模拟出M型风电运维船波浪航行时的波浪增阻与纵摇、垂荡情况,将数值仿真计算结果与原三体船的试验数据进行比较,以此探索不同M型船船型对船舶波浪航行时的波浪增阻与纵摇、垂荡情况的影响。最终确定了耐波性能较优的船型方案,从而为M型风电运维船船型设计提供了一定的参考和借鉴。     

Integrated design optimization of spar floating wind turbines

A linearized aero-hydro-servo-elastic floating wind turbine model is presented and used to perform integrated design optimization of the platform, tower, mooring system, and blade-pitch controller for a 10 MW spar floating wind turbine. Optimal design solutions are found using gradient-based optimization with analytic derivatives, considering both fatigue and extreme response constraints, where the objective function is a weighted combination of system cost and power quality. Optimization results show that local minima exist both in the soft-stiff and stiff-stiff range for the first tower bending mode and that a stiff-stiff tower design is needed to reach a solution that satisfies the fatigue constraints. The optimized platform has a relatively small diameter in the wave zone to limit the wave loads on the structure and an hourglass shape far below the waterline. The shape increases the restoring moment and natural frequency in pitch, which leads to improved behaviour in the low-frequency range. The importance of integrated optimization is shown in the solutions for the tower and blade-pitch control system, which are clearly affected by the simultaneous design of the platform. State-of-the-art nonlinear time-domain analyses show that the linearized model is conservative in general, but reasonably accurate in capturing trends, suggesting that the presented methodology is suitable for preliminary integrated design calculations.     

Environmental lumping for efficient fatigue assessment of large-diameter monopile wind turbines

Fatigue damage is one of the governing factors for the design of offshore wind turbines. However, the full fatigue assessment is a time-consuming task. During the design process, the site-specific environmental parameters are usually condensed by a lumping process to reduce the computational effort. Preservation of fatigue damage during lumping requires an accurate consideration of the met-ocean climate and the dynamic response of the structure. Two lumping methods (time-domain and frequency-domain) have been evaluated for a monopile-based 10 MW offshore wind turbine, both based on damage-equivalent contour lines. Fatigue damage from lumped load cases was compared to full long-term fatigue assessment. The lumping methods had an accuracy of 94–98% for the total long-term fatigue damage and 90% for individual wind speed classes, for aligned wind and waves. Fatigue damage was preserved with the same accuracy levels for the whole support structure. A significant reduction of computational time (93%) was achieved compared to a full long-term fatigue assessment. For the cases with 30° and 60° wind-wave misalignment, there was a mean underestimation of approximately 10%. Variations in penetration depth did not affect the selection of the lumped sea-state parameters. This work presents a straightforward method for the selection of damage-equivalent lumped load cases, which can adequately preserve long-term fatigue damage throughout the support structure, providing considerable reduction of computational effort.     

Experimental field study of floater motion effects on a main bearing in a full-scale spar floating wind turbine

In this paper we present a full-scale experimental field study of the effects of floater motion on a main bearing in a 6 MW turbine on a spar-type floating substructure. Floating wind turbines are necessary to access the full offshore wind power potential, but the characteristics of their operation leave a gap with respect to the rapidly developing empirical knowledge on operation of bottom-fixed turbines. Larger wind turbines are one of the most important contributions to reducing cost of energy, but challenge established drivetrain layouts, component size envelopes and analysis methods. We have used fibre optic strain sensor arrays to measure circumferential strain in the stationary ring in a main bearing. Strain data have been analysed in the time domain and the frequency domain and compared with data on environmental loads, floating turbine motion and turbine operation. The results show that the contribution to fluctuating strain from in-plane bending strain is two orders of magnitude larger than that from membrane strain. The fluctuating in-plane bending strain is the result of cyclic differences between blade bending moments, both in and out of the rotor plane, and is driven by wind loads and turbine rotation. The fluctuating membrane strain appears to be the result of both axial load from thrust, because of the bearing and roller geometry, and radial loads on the rotating bearing ring from total out-of-plane bending moments in the three blades. The membrane strain shows a contribution from slow-varying wind forces and floating turbine pitch motion. However, as the total fluctuating strain is dominated by the intrinsic effects of blade bending moments in these turbines, the relative effect of floater motion is very small. Mostly relevant for the intrinsic membrane strain, sum and difference frequencies appear in the measured responses as the result of nonlinear system behaviour. This is an important result with respect to turbine modelling and simulation, where global structural analyses and local drivetrain analyses are frequently decoupled.     

Experimental study on seismic vibration control of an offshore wind turbine with TMD considering soil liquefaction effect

Wind energy is clean and sustainable. Taiwan is establishing offshore wind farms using wind turbines in the Taiwan Strait. However, these are located in an earthquake-prone area with sandy seabed conditions. To ensure their safety and reliability, the turbines’ support structure must be protected against wind, waves, and seismic loads. Tuned mass dampers (TMDs) are commonly employed to reduce structural vibrations. A TMD is more simply incorporated into turbine structures than are other energy dissipation devices. In this study, a 1:25-scale test model with a TMD was constructed and subjected to shaking table tests to experimentally simulate the dynamic behavior of a typical 5-MW wind turbine with a jacket-type support structure and pile foundation. The scaled-down wind turbine model has a nacelle without rotating blades; therefore, the aerodynamic and rotational effects due to the rotating blades were ignored in this study. A large laminar shear box filled with saturated sandy ground was used to simulate the typical seabed conditions of Taiwanese offshore wind farms. The TMD system was designed to be tuned the first-mode frequency of the test model. Two ground accelerations, selected by considering wind farm site condition and near-fault characteristics, were used for excitation in the test. The responses of the test model with and without the TMD system were compared, and the influence of soil liquefaction on the effectiveness of TMD vibration control was addressed.